Magnetic holder for the Automatic Osmolator sensors

Magnetic holding devive for Turbelle Stream Pumps, Comline Filter's, Protein Skimmer's and Wave boxes

Replaces the 6080.230

Universal holder for attachment up to a glass thickness of 12 mm

Universal holder for attachment up to a glass thickness of 15 mm 

Dimensions: diam. 60 mm (2.3 in.) x W 15 mm (.59 in.).

For - 6065, 6085, 6125, 6105, 6155 6205, 6305 ( Depending on glass thickness )

1 x pair

Up to a glass thickness of 27 mm consisting of two equally dimensioned magnet halves of a width of 20 mm (.78 in.) each.

For - 6065, 6085, 6125, 6105, 6155, 6205, 6305 ( Depending on glass thickness )

1 x pair

attachment to magnet holders 6065.50 and 6205.50; suitable for the reduction of pumping noises.

Holder for Turbelle® stream and e-jet; attachment to a glass thickness of up to 19 mm (.74 in.), suitable for the reduction of the pumping noise.

Holder for Turbelle® stream and e-jet; attachment to a glass thickness of up to 25 mm (.98 in.), suitable for the reduction of the pumping noise.

For the attachment of classic style pumps to horizontal pane covers, we recommend the use of the mounting bracket made of high-grade steel in combination with the mounting clamp supplied along with the pump.

Universal holding clamp - Stainless steel

 For Tunze Classic pumps 2002 / 4002

Replacement Screw M6x12 V4A

Holder for TS mounting bar made of glass-fibre reinforced polycarbonate

970 mm x 25 mm x 15 mm, made of plastic with
60 % glass-fibre is absolutely resistant to corrosion, break and bending proof. May be sawn and milled, holes may be drilled.

Enables other fastening variants for the following applications:

Attachment for thicker panes (A)
Two long screws permit the attachment of the holding devices supplied, also on thicker panes up to 34 mm (1.33”).

Attachment for Rims (B)
The extension can be used to attach the holding device for aquarium rims up to 34mm (1.33”) thickness. The rim can project outward about 10mm (0.4”).

Supporting attachment for horizontal pane (C)
It allows attachment on horizontal aquarium panes for 4 to 8 cm (1,6” to 3,1”) with an adjustable support. Especially suitable for COMLINE units.

Holding device for Turbelle ®, electrodes, heaters, etc

Holding device extension, enables three other fastening variants:

Holding device extension (A)
Extension of the perforated rail by 20 cm

Glass top attachment (B)
Used to attach the perforated rail below glass tops with a width of 4 to 15 cm.

Adhesive attachment (C)
The clamp holding device is not required for this type of attachment. Instead, two threaded platelets have to be stuck to the aquarium pane with silicone adhesive 104.72 for the perforated rail.

Adhesive attachment's
Two threaded platelets & bolts can be used to stick to the aquarium pane with silicone adhesive 104.72 to hold the perforated rail.

Permits TUNZE ® holding rail to be fitted to vertical glass panes without the use of the usual clamp holders.
In case of removable cover frames the bracket is covered and secured at the same time.

Suction cup holder for Turbelle with 3 suction cups

Special suction cups 3 pcs for
Turbelle ® / Comline and many commercially available applications, extremely long-life with undercut for silicone application

Silencer holding device; supplement to the Turbelle ® holding device supplied; suitable to reduce the pumping noises.

9 Replacement rubber feet for the magnetic holders

Heater and electrode holding device for TS mounting bar made of glass-fibre reinforced polycarbonate